Find the
coefficient of water plane.
Station:
AP 2 3 4 FP
??
breadth (m): 0.6 1.1 1.6 0.9 0.1
Length of
water plane is 15 meters.
|
|||||||||||||||||||||||||
|
|
||||||||||||||||||||||||
|
|
||||||||||||||||||||||||
Table
1
|
Station
|
AP
|
1
|
2
|
3
|
4
|
5
|
FP
|
|||||||||||||||||
??
Breadths
|
2.5
|
4.73
|
5.88
|
6.0
|
5.09
|
3.11
|
0.0
|
||||||||||||||||||
Table
2
|
Station
|
AP
|
-1
|
-2
|
-3
|
|
|
|
|||||||||||||||||
??
Breadths
|
2.5
|
1.88
|
1.25
|
0.63
|
|
|
|
The tables 1 and 2 of a vessel are ?? breadths of water plane between
perpendiculars and appendage respectively. The lengths between perpendiculars
and appendages are 60m and 7.5m respectively. Find the LCF of the water plane
from mid ship.
|
|||||||||||||||||
|
|||||||||||||||||
Find CWP and TPC of a vessel whose ?? breadths
of the water plane as follows:
Station: AP 1 2 3 4 FP
?? Breadths (M) 1.0 1.44 1.55 1.33 0.89 0.2
Length between perpendiculars is 14 meters.
Consider the nearest value.
|
|||||||||||||||||
|
|
||||||||||||||||
|
|
||||||||||||||||
The ship???s model estimates the
|
|||||||||||||||||
|
|
||||||||||||||||
|
|
||||||||||||||||
Air pipes
in tanks are generally located:
|
|||||||||||||||||
|
|
||||||||||||||||
|
|
||||||||||||||||
The
surface of each blade of propeller when viewed from aft is known as the
__________________
|
|||||||||||||||||
|
|
||||||||||||||||
|
|
||||||||||||||||
The
cyclic angular motion of a ship about the ford ???aft axis under the action
of waves is known as:
|
|||||||||||||||||
|
|
||||||||||||||||
|
|
||||||||||||||||
Curves of
immersed cross-sectional area of a ship , plotted against draught for each
transverse section , are known as
|
|||||||||||||||||
|
|
||||||||||||||||
|
|
||||||||||||||||
Peak
tanks are tested by:
|
|||||||||||||||||
|
|
||||||||||||||||
|
|
||||||||||||||||
Plates
used to connect stern frames to flat plate keel are called:
|
|||||||||||||||||
|
|
||||||||||||||||
|
|
||||||||||||||||
Mark: 4
|
|||||||||||||||||
In- water
survey in lieu of a one of the two docking surveys in a 5-year period may be
accepted when:
|
|||||||||||||||||
|
|
||||||||||||||||
|
|
||||||||||||||||
Thickness
of strakes of bottom plating is increased in which of the following regions
of the ship?
|
|||||||||||||||||
|
|
||||||||||||||||
|
|
||||||||||||||||
In a
shell expansion plan, plate D5 refers to:
|
|||||||||||||||||
|
|
||||||||||||||||
|
|
||||||||||||||||
|
|||||||||||||||||
|
|||||||||||||||||
|
|||||||||||||||||
|
Which component in the given Figure is a bulkhead? What type of bulkhead
is it?
Identify the part no. 3 of the given figure :
|
||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||
The mass
of a ship without cargo, fuel, stores, water, crew etc that a ship carries is
known as:
|
||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
Why the frictional resistance increases when
the draft increases?
|
||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
Find the TPC when offset of water plane is as follows:
Station AP 2 3 4 5 FP
?? breadth (m) 0.9 1.5 2.1 1.6 0.9 0.1
Length of water plane is 15
meters.
|
||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
Panting arrangements are usually fitted up to
__________ percent of ship???s length abaft the stem.
|
||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
In longitudinally framed double bottoms, in
frame
spaces where there are no solid floors,
the
brackets on tank sides and center girder
should
not be more than ___________ apart.
|
||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
As per conditions of assignments, the minimum
height of air
pipe
openings must be ________ on
the freeboard deck
|
||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
The primary purpose of fitting a bulbous bow is
to:
|
||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
The purpose of providing tumble home is to:
|
||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
In longitudinally framed double bottoms, solid
plate floors are fitted at _________ frame space in pounding region and at ________frame
space under the main engine.
|
||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
A box barge, length 35m and
beam 7m, is floating at draft 3m in brackish water, density 1.012t/m3.
The length of mid-ship
compartment is 10m and full depth. The compartment is bilged. Find the new
draft.
|
||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||
No comments:
Post a Comment